Panasonic WV-SW598 Przewodnik Instalacji

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number i

Do not damage the power cable. Do not damage, fabricate, twist, stretch, bundle, or forci-bly bend the power cable. Do not place heavy objects on it,

Periodically images on the screen appear to be dis-tortedWhen the camera is installed in a location where it is sub-ject to small vibrations (for exam

Position refreshDuring the use for a long period of time, the preset posi-tions may become inaccurate. When “Position refresh” is set for the create

Precautions for installationPanasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper instal

Take notice of humidity. Install this product when the humidity is low. If this product is installed during rainfall or when there is high hu

Major operating controlsExternal I/O cableMicrophone input cable (connector: white)Audio output cable (connector: black)Network cable with cable coupl

<Rear view of the main body with the main sunshield rear cover detached>Water-resistant capMain nameplateSD memory card slotLive indicatorAccess

Initialize the cameraUse the INITIAL SET switch to reset the settings of the camera to the default. IMPORTANT: • Thesettingsincludingthenetwork

Insert/remove an SD memory cardHow to insert an SD memory cardIMPORTANT: • WheninsertinganSDmemorycard,makesurethedirection. Step 1Pull

Step 7First, insert the tab on the bottom of the main sunshield rear cover into the main body, and then push the tab on the top of the main sunshield

WARNING:• To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with the installation instruc-tions.• All wo

Installations/ConnectionsCaution:•FORULLISTEDMODEL(S),ONLYCONNECT24VACCLASS2POWERSUPPLY(UL1310/CSA223)orLIMITEDPOWER SOURCE (IEC/E

How to detach the housing baseBefore attaching the camera to a custom-made mount bracket, detach the housing base and attachment pipe from the camera

InstallationBefore starting installation/connection, make sure that the power cable is not connected to the main power supply.Refer to the “Precaution

Step 4Mount the camera to the bracket. q Attach the housing base to the mount bracket using the hexagon screws (M5, 4 pcs.) attached to the housing

Fixing screws (3 pcs.)Positioning pinCameraProtection CoverHousing baseStep 5Attach the front and rear sunshields (accessory) to the camera. q Put th

Step 7Fix the front and rear sunshields on the camera using the front/rear sunshield fixing screw (accessory).(Recommended tightening torque: 0.72 N·m

ConnectionCaution:•Before starting connections, make surethat the power connection (24 V AC power cord or LAN cable) is discon-nec

• 24 V AC power supply connector kit (accessory)Recommended specification of cable (wire)Wire size (AWG), stranded wire#24(0.22 mm)#22(0.33 mm)#20(0.5

• External I/O cableIMPORTANT: • Off, input, and output of the external I/O terminal 2and 3 can be switched by configuring the setting. Th

Connection example (Refer to page 26 for how to connect the cables.) When connecting with a PC directlyPower supply(24 V AC)LAN cable (category 5e or

ContentsImportant safety instructions ...

Connecting to a network using a PoE+ hub when the temperature is –30 °C {–22 °F} or less* When connecting to a network using a PoE+ hub when the temp

Configure the network settingsConfiguring the camera so that it can be accessed from a PCThe following are descriptions for when the camera with defau

v Iftheinstallationscreenoftheviewersoftware“NetworkCameraView4S”isdisplayed,followtheinstructionsofthewizard to start the install

TroubleshootingBefore asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after ch

Symptom Cause/solutionReference pagesLive indicator keeps on blinking orange approx. in 2 seconds intervals. •UPnPTM error has occurred since the po

Symptom Cause/solutionReference pagesIt is hard to see images with the camera when there are raindrops on the dome cover. The effectiveness of the ra

Specifications• BasicPower source: 24VAC±15%,PoE+device(IEEE802.3atcompliant)orTestedPoEinjector(60W)Power consumption: AC power supply:

Minimum illumination: Color: 0.5 lx {0.0465 foot-candle} (F1.6, Auto slow shutter: Off (1/30 s), AGC: High) 0.031 lx {0.0029 foot-candle} (F1.6, A

• NetworkNetwork: 10BASE-T/100BASE-TX, RJ-45 connectorResolution: •Imagecapturemode: 2 mega pixel [16:9] H.264 JPEG (MJPEG)1920x1080/640x360/3

Standard accessoriesInstallation Guide (this document) ...

Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) D

40

41

42

43

44

45

For U.S. and Canada:Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North Americawww.panasonic.com/business

Limitation of liabilityTHIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE

Main functionsH.264 dual stream and JPEG (MJPEG) triple encoding at 1920x1080/30 fpsH.264 dual stream output and JPEG (MJPEG) output can be simultaneo

System requirements for a PCCPU: Intel® CoreTM 2 Duo 2.4 GHz or faster recommendedMemory: 512 MB or more (A minimum of 1 GB memory is required when

Trademarks and registered trademarks • Microsoft,Windows,WindowsVista,InternetExplorer,andDirectXareeitherregisteredtrademarksortradema

PrecautionsRefer installation work to the dealer.Installation work requires technique and experience. Failure to observe this may cause fire, electric