Panasonic WVCS850_SERIES Instrukcje Operacyjne

Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Model No. WV-C

11 Setup Menu Description● PRESET(1) Position (POSITION SET)POSITION SET adjusts the camera picture by panning, tilting, zooming and focusing.See pag

12● AUTO PAN KEYThis setting assigns SEQ, SORT, AUTO PAN or PATROL (PLAY) to the AUTO key on the controller.After setting this, the AUTO key performs

13(6) Password Lock ON/OFF (PASSWORD LOCK ON/OFF)This setting controls access to the PRIVACY ZONE to be free or limited. If PASSWORD LOCK ON isselecte

14Notes:• The result of field setup of the mask area and level adjustment is fed back (effected) to the lensiris control in ALC mode.• Select OFF for

15(7) White Balance (WHITE BAL)You can select one of two modes for white balance adjustment as follows:• ATW (Auto Tracing White Balance)In this mode,

16SETTING PROCEDURESThe following setting procedures are described on the assumption that this model is used in combinationwith the WJ-SX550B Matrix S

17 Preset● Preset Menu Display1. Displaying the preset menu directly(1) Move the cursor to PRESET 1 and move the joystick to theright or left to sel

183. Pan OffsetIf the camera is replaced with a new one, Pan Offset is used toadjust its positions to be the same as before except patrol setting.The

19● Preset ID Setting1. Move the cursor to PRESET ID on the preset setting menu andselect ON or OFF by moving the joystick to the right or left.ON: Pr

20To Set a Display Position for a PRESET ID1. Move the cursor to POSI and press the CAM (SET) key. Thedisplay position set menu appears.2. Using the j

2The serial number of this product may be found on thetop of the unit.You should note the serial number of this unit in thespace provided and retain t

21● Dwell Time Setting• Move the cursor to DWELL TIME and set a dwell time by movingthe joystick to the right or left. Dwell time changes as follows:T

22 Deleting Preset Positions1. Move the cursor to PRESET 1 and select the position number tobe deleted by moving the joystick.2. Press the CAM (SET)

23 Auto Mode Selection1. To set auto modeMove the cursor to AUTO MODE and select a mode by movingthe joystick to the right or left. Modes change as f

246. To set endless turn ON/OFFMove the cursor to ENDLESS, and move the joystick to the right orleft to set endless turn ON or OFF.ON: The camera pans

25 DIGITAL FLIP ON/OFF• Move the cursor to DIGITAL FLIP and select ON or OFF by mov-ing the joystick to the right or left.OFF: Tilt range is limited

26** ZONE NUMBER 3*/8 ** PAN/TILT →PUSH SET ZOOM/FOCUS →PUSH SET ZONE SCALE ••••|•••• SET DEL L HRETZONE setting menu** ZONE

273-6• To complete new settings and repeat another setting, move the cursor to SET and press the CAM(SET) key. The ZONE NUMBER Selection menu returns.

283. Move the cursor to PUSH SET on the ZOOM/FOCUS line, thenpress the CAM (SET) key. ZOOM/FOCUS is highlighted and “UZOOM D/L FOCUS R” appears.4. Mov

29To Quit Editing• To return to the Area Title menu, move the cursor to RET, thenpress the CAM (SET) key.• To cancel one area title, move the cursor t

30PATROL LEARN with a Controller Having PATROL Key1. Press the PATROL key and the CAM (SET) key simultaneously tostart PATROL LEARN. The setup menu ch

3CONTENTSPREFACE ... 4FEATURES ...

31● Alarm IN/OUT (ALARM IN/OUT)Move the cursor to ALARM IN/OUT, then press the CAM (SET) key.ALARM I/O submenu appears.Note: While the camera is in AF

32 ** PASSWORD? ** 0 1 2 3 4 5 6 7 8 9 . . . ↑OK RESETNEW PASSWORDRET PASSWORD ** SPECIAL 1 **PRIVACY ZONE OFF(E

33NEW PASSWORD4. To change the password in step 3-3 above, move the cursor fromOK to NEW PASSWORD, then press the CAM (SET) key. NEWPASSWORD menu appe

34● Electric Zoom ON/OFF (EL-ZOOM ON/OFF)The electric zoom magnifies a scene 10-fold. With a 22-fold opticalzoom lens, the camera is capable of 220-fo

35 Camera Setting1. To Display the Camera Setting Menu• Move the cursor to CAMERA , and press the CAM (SET) key.The camera setting menu is displayed

36 CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ÄÜÖÆÑÅ SPACE POSI RET RESET

37(2) ALC Mode with SUPER-D2 OFF1. Move the cursor to the SUPER-D2 parameter and select OFF.(When you select MANUAL, SUPER-D2 is not available.) The i

384. Shutter Speed Setting (SHUTTER)Note: When ON is selected for SUPER-D2 on the ALC CONT menu,this item is not available.To select electronic shutte

39• When ON is selected for SUPER-D2 on the ALC CONT menuNotes:• When ON is selected for SUPER-D2 in the ALC CONT menu, FIXis not available for this i

407. Use the joystick to match the vertical phases for both video outputsignals as closely as possible. (COARSE adjustment can beincremented in steps

4• High quality picture of 737 x 575 pixels.• Minimum illumination of 1 lx for C/L, 0.06 lxfor B/W.• Super-Dynamic2 extends the dynamicrange up to 48

41(2) Automatic White Balance Control Mode (AWC)1. Display SET UP on the monitor screen.(Refer to Setup Menu Display on page 16 for details on display

429. Motion Detector Setting (MOTION DET)1. Display SET UP on the monitor screen.(Refer to Setup Menu Display on page 16 for details on display-ing th

Important Notices:• The object of motion detection should meet the following conditions.1) It should be larger than 1/48 of the size of the picture sc

4411. Special 2 Menu (SPECIAL2)This menu lets you adjust and set up the picture quality to meet yourrequirements.• Display SET UP on the monitor scree

45(4) BWMove the cursor to BW and select AUTO, ON or OFF by movingthe joystick to the right or left. Default : OFF.AUTO: The camera selects black and

46 RS485 Setup● Initial Camera Communication ParametersIn an RS485 chain the matrix switcher, PC, controllers and cameras should be set to the same p

47ALARM DATASpecifies alarm transmission mode depending on the protocol selected by the 8-bit DIP switch.POLLING: Transmits the alarm data in response

48• The following steps of installation and connection should be taken by qualified service personnel orsystem installers and should conform to all lo

49Unit NumberSwitch 1, an 8-bit DIP switch, specifies unit number or returns tothe factory default settings for Panasonic’s protocol.When the unit num

501234ON5678Switch positionUnitnumber1234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON56781234ON5678123

5 Camera CleaningEven if this function is used, it may be produced noise on the monitor screen, or the preset position maybe deviated in the cause of

51Full duplex (4 line) *BP 2BP 1 FunctionSwitchpositionFunctionSwitchpositionRS485 SettingThe 4-bit DIP switch in used forRS485 termination.ONMarking1

525. Tighten the fixing screw M3 (provided).Notes:(1) Tighten the camera fixing screw with ascrewdriver.(2) Follow the instructions given here toensur

How to Assemble the Cable with theAccessory ConnectorStrip back the cable jacket approx. 3 mm (0.1inch) and separate the individual conductors.Recomme

54GreyWhitePinkYellow green or light blueBlackBrownRedOrangeYellowLight blue or greenBluePurpleWire colourWire colour• RS485 ConnectionNote:Use the ca

55Note: When any peripheral is turned off and turned on again, the camera is also turned off and turnedback on.SYSTEM CONNECTIONS1 2 34 5 67 8 9MON CA

48 dB (SUPER-D2 ON)56Zoom ratioBright objectSmearWhen the camera is aimed at a bright light, suchas a spotlight, or a surface that reflects brightligh

57ControlsAUTO FOCUSPanning rangeWeights and dimensions indicated are approximate.Specifications are subject to change without notice.360° endlessposs

58Selecting a PRESET position From #1 to #64#1 [1] + [CAM FUNC]#10 [1] + [0] + [CAM FUNC]#64 [6] + [4] + [CAM FUNC]AUTO PANON [6] + [5] + [CAM FUNC]OF

N0701-1071 V8QA5749BN Printed in JapanN 19 Gedruckt in JapanImprimé au JaponImpreso en JapónStampato in Giappone2001 © Matsushita Communication Indust

64. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera when itis dirty.When the dirt is hard to

7y Camera Mounting Baseu Panning Start Pointi Fall Prevention Wireo Decoration Cover!0 Dome Coverq Alarm Input Connectorw Alarm Output Connectore Vide

9ShutterSpeedSelectionSensitivityUpON/OFFWHITEBALAWC ATWSuper-D2OFFLight ControlALC/MANUALSuper-D2ONManualLevelAdjustment(Contrast)ManualMaskAreaS

10Open Special 2 F2 keyThe keys (switches) to use for setup are as shown in the table below. The joystick on the connected con-troller may also be use