Panasonic WVRM70 Instrukcje Operacyjne

Camera ControllerWV-RM70EBefore attempting to connect or operate this product,please read these instructions completely.FRANÇAISDEUTSCHENGLISHESPAÑOL

-8-5. Set switch (SW5) on the board to choose the dataline selection mode for data terminal.4 LINE : normal connections aremade.2 LINE : simplified co

-9-3. System Connections Basic ConnectionTLCamera WV-CP610Camera WV-CS300Pan/TiltReceiverCamera Controller WV-RM70ETime Lapse VTRMonitorMotion Detect

-10- System 100 System 300TLTLTime Lapse VTRPCWV-CU101WV-CS300WV-BS200WV-CP610 WV-CP610WV-RM70EWJ-SW208WJ-MP404WJ-SQ508WV-CU300RS-485 RS-485ALARM O

-11- Cable-loss Compensation SettingThe maximum cable length in the system is approximately 1,200 meter.See the diagram below and set up the cable-lo

-12-4. Connection with the PersonalComputer 4 Data Line (Dip Switch SW5 : 4 LINE) 2 Data Line (Dip Switch SW5 : 2 LINE)T(A)T(B)R(A)R(B)R(A)R(B)T(A)T

-13-OPERATING PROCEDUREBefore starting the following procedures, all system components should be turned on.1. Mode SelectionThis controller can select

-14-2. Entering Program MenuBy pressing the Program (PROG) Switch for morethan 2 seconds, when Mode Selection Switch isselected at Normal (NORMAL) pos

-15-3. Camera ControlMove the cursor to the “Camera Control” positionby pressing the Up (D) Switch or the Down (C)Switch, then press the Set Switch to

-16-3-2. Electronic Sensitivity UpThe following function is available only when speci-fied camera with the electronic sensitivity feature isused.1. Di

-17-3-4. Back Light Compensation (BLC)The following function is available only when speci-fied camera with the Auto/Preset BLC Function isused.1. Disp

CAUTION:Before attempting to connect or operate this prod-uct, please read the label on the bottom.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO

-18-2. Press the Right (B) Switch or the Left (A) Switch toselect desired mode, “ATW” or “AWC”.After completing the above settings, press theProgram (

-19-2. Press the Up (D) Switch or the Down (C) Switch tomove the Pan/Tilt Head toward up or down. Pressthe Right (B) Switch or the Left (A) Switch to

-20-2. Press the Left (A) Switch repeatedly to turn on oroff the user’s auxiliary switch 1 in the Receiver (WV-RC100, WV-RC150 or WV-RC160).3. Press t

-21-5. Camera Set Up The following functions are only available with thecamera that has set up functions such as thePanasonic WV-CP610 or WV-BP510 ser

-22-** Program Menu **Camera Control *Receiver Control *Camera Set Up *Controller Set Up *6. Controller Set Up6-1. Entering Controller Setup Menu1

-23-6-2. System Setup1. Display the Controller Set Up Menu by repeatingthe previous procedures.** System **Camera ID Off *Cable Comp SAlarm

ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789().,'":;&#!?=+-*/%$ÄÜÖÆÑÅ←→SpacePosi Return Clear...ABCDEFGHIJKLMNOPQRSTUVWXYZ012345678

ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789().,'":;&#!?=+-*/%$ÄÜÖÆÑÅ←→SpacePosi Return ClearDOOR ...-25-Fig. 249. When all characters in

-26-The Camera ID display position can be placedanywhere on the screen by pressing the Up(D) Switch, Down (C) Switch, Left (A) Switchand Right (B) Swi

** Communication **Unit Number 1Baud Rate 9600Data Bit 8Parity Check NoneStop Bit 1Xon/Xoff Not UseWait Time OffDel

-1-CONTENTSPREFACE ...

** Communication **Unit Number 1Baud Rate 9600Data Bit 8Parity Check NoneStop Bit 1Xon/Xoff Not UseWait Time OffDel

-29-(4) Parity Check Setting1. Display the communication Menu as shown inFig. 30 by repeating the previous procedures.2. Move the cursor to the “Parit

-30-←Alarm→Notes :• “Alarm” display position can be placed atupper or lower right side of the monitor screen.Refer to the Title Setting on page 23 for

-31-Note: When the ALL RESET mode is being per-formed, the picture may be disturbed momen-tarily.This is normal and is not indicative of a prob-lem.q

-32-SPECIFICATIONSPower Source : DC12V (DC 10.8V - 16.0V), 230mACamera Input : Composite Video Signal: 1.0Vp-p / 75ΩVD2 Output Signal: 2.5Vp-p / 75ΩDa

Ambient Operating Temperature : −10˚C - +60˚C (14˚F - 140˚F)Ambient Operating Humidity : Less than 90%Dimensions : 138 (W) x 185 (D) x 51 (H) mm5-7/16

N0495-3048 YWV8QA3532DN Printed in JapanN 19 Gedruckt in JapanImprimé au JaponImpreso en JapónMatsushita Electric Industrial Co., Ltd.Central P.O. Box

-2-PREFACEThe WV-RM70E Camera Controller, when combinedwith the optional WV-CP610 and WV-BP510 seriesCCTV Camera, enables remote control of camera set

-3-PRECAUTIONS• Do not attempt to disassemble the unit.In order to prevent electric shock, do not removescrews or covers. There are no user-serviceab

-4-MAJOR OPERATING CONTROLS AND THEIR FUNCTIONSREMOTEOPERATECamera Controller WV-RM 70PROGALARMRESETNORMALSYSTEMALARM OFFONOFFINOUTTERM VIDEO CAME

-5-1. Power Indicator (OPERATE)This indicator lights up when DC power is suppliedto the DC 12V Input Terminal.2. PC Remote Indicator (REMOTE)This indi

-6-ALARM OUT: The alarm output signal is providedat this terminal for the Time Lapse VTR.12. Data TerminalThese terminals are used to transmit / rec

-7-CONNECTIONS1. Dip Switch SettingBefore connecting this controller, confirm the DipSwitch Setting if the system setting change is required.Pulse (VT