Panasonic CZ-ESWC2 Instrukcja Instalacji Pobierz pdf (Strona 14)

3-6-2. Installing the Ceiling Panel

After completing the wiring process, install the supplied

wiring cover before installing the panel.

It is not possible to install the wiring cover after installing

the panel.

The power must be turned ON in order to change the ﬂ ap

angle. (Do not attempt to move the ﬂ ap by hand. Doing so

may damage the ﬂ ap.)

(1) Insert the temporary fasteners (stainless steel) on the

inside of the ceiling panel into the square holes on the

unit to temporarily fasten the ceiling panel in place.

(Fig. 3-20-1)

The ceiling panel must be installed in the correct

●

direction relative to the unit. Align the REF. PIPE and

DRAIN marks on the ceiling panel corner with the

correct positions on the unit.

To remove the ceiling panel, support the ceiling panel

●

while pressing the temporary fasteners toward the

outside. (Fig. 3-20-1)

(2) Align the panel installation holes and the unit screw

holes.

(3) Tighten the supplied washer head screws at the 4

panel installation locations so that the panel is

attached tightly to the unit. (Fig. 3-20-2)

(4) Check that the panel is attached tightly to the ceiling.

At this time, make sure that there are no gaps between

●

the unit and the ceiling panel, or between the ceiling

panel and the ceiling surface. (Fig. 3-21)

If there is a gap between the panel and the ceiling,

●

leave the ceiling panel attached and make ﬁ ne

adjustments to the installation height of the unit to

eliminate the gap with the ceiling. (Fig. 3-21)

CAUTION

If the screws are not sufﬁ ciently

●

tightened, trouble such as that shown

in the ﬁ gure below may occur. Be sure

to tighten the screws securely.

If a gap remains between the ceiling

●

surface and the ceiling panel even

after the screws are tightened, adjust

the height of the unit again.

The height of the unit can be adjusted from the

ceiling panel corner hole, with the ceiling panel

attached, to an extent that does not affect the

unit levelness, the drain hose, or other elements.

Square hole in unit

Temporary

fastener

Push when

you remove

Temporary

fastener

Fig. 3-20-1

Drain tubing corner

Refrigerant tubing

corner

DRAIN mark

Panel installation hole

(4 locations)

REF. PIPE

mark

Washer head

screws

Ceiling panel

After completing the

wiring process, install

the supplied wiring cover

before installing the panel.

It is not possible to install

the wiring cover after

installing the panel.

Fig. 3-20-2

Do not allow

gaps

Ceiling panel

Main unit

Ceiling surface

Fig. 3-21

Insert a wrench

or other tool into

the corner cover

installation hole

and make fine

adjustments to

the unit nut.

Fig. 3-22

Air leakage

Air leakage from

ceiling surface

Staining

Condensation, water leakage

Adjust so that there are no gaps.

Fig. 3-23

Fig. 3-19-1

Screw (supplied)

M4-8 or 5/32" – 5/16"

Wiring cover (supplied) Power supply outlet

Inter-unit control wiring

Fig. 3-19-2

VRF_Indoor_US.indb 14VRF_Indoor_US.indb 14 2011/09/30 12:22:572011/09/30 12:22:57

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 83 84

Komentarze do niniejszej Instrukcji

Brak uwag

Panasonic CZ-ESWC2 Instrukcja Instalacji Strona 14

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Klimatyzatory typu split Panasonic CZ-ESWC2